Jump to content
Home Page  | How to Join  | Official Merchandise  | Western Meet | Eastern Meet | Meet Photos | Technical Info  | Museum  | Parts Sources  | Officers
Sign in to follow this  
Jared Richey

SS Hockey Sticks

Recommended Posts

I'm putting the call out again for a set of preferably used SS 71 rear hockey sticks. I want to put these in the hands of a few people in this area who have the equipment to make something like this.

I currently have them on one of my cars but as any that is familiar would know it's an act of Congress to take them off. I do not want to be responsible for any NOS ones... Prefer a used set to use. I would be willing to buy a set if the price is right... Or buy them with the agreement that when I'm done with them you can buy them back for the same amount.

Share this post


Link to post
Share on other sites

I talked to someone at the Parts Place and they were going to have there supplier manufactor the upper mouldings but I don't see them listed

Share this post


Link to post
Share on other sites

I'll agree.....way too much work to take them off....... hopefully someone will come up with a set for you Jared.

Mine are in good shape but put me down for a new set once you get this done!

Steve

Share this post


Link to post
Share on other sites

The "hockey sticks" are on a 71 SS car. They are on the back tail panel, on the end caps above the normal trim pieces. The panel is then blacked out between the trim. They look like the lower end cap trim only bent with a tighter curve and are held on with a nut on a stud opposed to screws for the lower pieces. Actually they look like this, off the car.....IMG_20180826_115504.thumb.jpg.8483f5712222e6a13d5c40b489258922.jpgIMG_20180826_115540.thumb.jpg.7a761188d62fbcf082be76b669d15dbd.jpg

IMG_20180826_115520.jpg

IMG_1121.JPG

Share this post


Link to post
Share on other sites

The hockey sticks is the small trim piece that bolts to the end cap on 1971 SS .top piece in picture

0510sc_06z+1972_chevrolet_monte_carlo+rear_view.jpg

Share this post


Link to post
Share on other sites
On 1/6/2019 at 11:22 AM, 1970mcss said:

I talked to someone at the Parts Place and they were going to have there supplier manufactor the upper mouldings but I don't see them listed

Can you call whoever you talked to and verify? If there going to mass produce that would be good. Hopefully they make them out of stainless.

Share this post


Link to post
Share on other sites

Jared do you need both?  I think I have one still attached to a piece not attached to a car, I have to check. Give me a day or so and I will get back to you.

Share this post


Link to post
Share on other sites

Jared, I think it has Joe the owner. He was going to figure out the measurement of the stud location and talk to the people that produce the lower mouldings. I have a 70 so Never followed up. You might want to call them and ask. Good luck and keep us posted...

Share this post


Link to post
Share on other sites

Ok.

Willie, 1 might work, I think it's a flip copy anyway. 

Thanks

Share this post


Link to post
Share on other sites

I just sent the parts place a message

Share this post


Link to post
Share on other sites

 Not a flip copy. Look at the pics I posted. Especially of the pair. They are left and right specific and have different part numbers for each. Also hard to see but the studs on the back are in slightly different locations .

Share this post


Link to post
Share on other sites

My response from the parts place...

 

We currently are in the process of making them, please contact us back again on the matter in a few weeks and we may have an update.


 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×