Leaderboard
Popular Content
Showing content with the highest reputation on 05/15/2022 in all areas
-
7 points
-
Not sure if anyone else has had dealings with Early Bird Restoration in Barrie, Ont. But I just picked up a few pieces... His prices are pretty good, (buys in bulk from Parts Place.) and it saves on all the duty and cross border fees. Looks like he has the ability to get just about anything.4 points
-
After doing the around the house chores , went to a small car cruise in Maysvill Ky a few miles away, at a pub bar kinda restaurant called the barrel house.. saw a 72 Monte I had never seen before in this area.. I know the DJ and he said moreand more first generation Montes are showing up at his cruises.. I did not get to meet the car owner but here are a few photos of the 72.. it looks like a decent ride but the dash is needing a lot of attention...4 points
-
went to a spring dust off show/cruise only monte there. went to a new thursday nite cruise me plus 2 other first gens4 points
-
Went to cruise in today of course I was the only first gen there had fun was a good time. My brother went to a show in Saratoga sent me a picture of Jess's old car. Hopefully he'll be at Carlisle I think he said he was going.4 points
-
3 points
-
3 points
-
2 points
-
2 points
-
Thanks Dennis.. I did the electrical and ran line from other room for hvac.. only part of this I probably won’t do is carpet.. the room leading into this room needs carpet as well and a pro installer can move the furniture 😃...2 points
-
2 points
-
2 points
-
2 points
-
1 point
-
1 point
-
1 point
-
I don’t wish that upon anyone. Drywall sucks. I did a monster room upstairs, made a secondary suite for Karen’s parents if they move in here( their old). HVAC, electrical I did all of it myself. EXCEPT, I hired a guy to finish the drywall. He was in and out in 3 days with very little mess. That would have been 6 months of misery for me. Well worth the money. Looks like you’re doing some good work. Keep it up. 👍1 point
-
Nice work Dennis, what kind of glue did you use to put the tree back together and throw it in the ditch ? 🤣 🌳1 point
-
Another Saturday project, started the sheet rock install on a small room upstairs over the kitchen that leads into over the garage, yesterday morning while it was cool in there.. making a small bedroom.. carry that upstairs was no easy task for an old man with a bad back.. but somehow I managed.. this is the worst part of this job...1 point
-
Hi Sammy, I have debated that thought in my little brain as well, but probably won’t mount them on the car before Carlisle.. it’s registered as modified anyway and I rally like the American racer black chrome wheels... after that I will begin turning the 71 a little less modified ., to street probably.. don’t think I can go original without all the parts . Thanks for asking... see ya soon 👋🏻. Ron...1 point
-
Mine will be 50 the 30th. I have the original registration from when ole red was brand spanking new1 point
-
ive got a blue print small block engine with dual plane air gap intake 2 inch spacer edelbrock carb 3 inch air filter no fitment problem1 point
-
1 point
-
Sucks though because they are screwed down but the heads are rusted enough that I can’t drive them back out Were they Phillips head head, square drive or Torx? My deck boards are installed with square drivew stainless steel screws and com out rather easily. This is one reason I spent the extra Money back in 1999 so I could replace boards if necessary but more than likely won't have because of Menards Trex style decking that was about 2/3rds of the Trerx cost back in the days of yore1 point
-
That does NOT look like any fun at all to me. I hate doing house type maintenance like that. My condolences1 point
-
A guy who burns wood for heat picked up all the cut wood today. The ugly stump went into the neighbors ditch to help control erosion. At least that’s my story. Done. So today I got started on the deck. I decided not to replace all the boards just the ones that are rotten. Gonna rain do I quit for the day. I got a few ripped out but plenty more. Sucks though because they are screwed down but the heads are rusted enough that I can’t drive them back out. So I’m having to break out the boards and pull the screws with a vise grip. Fun stuff. 225 bucks for a 5 gallon pail of deck paint/ stain. Omg 😳1 point
-
1 point
-
1 point
-
Looking good, mine will be done tomorrow, interior and spring cleanup1 point
-
Yeah… I had bourbon-infused extremities at the time 🤣😂. Mama wasn’t having my amorous attempts.1 point
-
1 point
-
Ed, I hope you never forget to remove that draw bar when no trailer is being pulled because it looks like it really sticks out a good way. That thing could really be a shin buster. rob1 point
-
1 point
-
I haven't seen one of those babies in years!! And she looks to be in great shape, considering!! Nice find Ron!!1 point
-
Lol! I'm running out of steam right now 😁. Have to work 4 dayshifts starting tomorrow (which means 3 probably, feeling sick already 😜), then vacation for 2 weeks. Hopefully I can get pretty far along with this one, then time to start preparing for Carlisle. I did start bolting a few parts on the car last night, so that's a start finally.1 point
-
1 point
-
1 point
-
1 point
-
1 point
-
Well it's been awhile since I updated. Lots of overtime, so progress has been slow. I had to recut and reposition the wheel well, buts it's welded and seams are sealed. Got the new quarter tacked in, so I hope everyone agrees it looks good lol. I've also got about 99% of my engine parts, so that is next on the list.1 point
-
1 point
-
Sounds like Jared is having love life issues, maybe you can shop around for something at Carlisle. Lots of wrench winches there. rob1 point
-
I totally agree and that’s what I thought. I didn’t find a bumper but I did find Karen when I was 36. So there is always a chance. Don’t give up hope. Lol.1 point
-
1 point
-
1 point
-
1 point
-
Larry, did you use a 30 watt electric soldering iron?? Or 60 watt? Or butane?1 point
-
1 point
-
1 point