Jump to content

Corvus

(Non-dues paying)
  • Posts

    22
  • Joined

  • Last visited

Reputation

1 Neutral

Profile Information

  • Legal Name
    David Lutter
  1. Yeah I've checked the tires, but they are smaller than what was originally on there when I bought it (275 up front). I'm guessing it's a combination of light up front and lots of spring travel. Just bothers me that the 6330 are supposed to be the stock height for the small block Monte. Maybe because it's missing the AC compressor? That shouldn't be much though. Oh well, I'll probably either hack these up or pony up more bucks for some drop springs. Just seems like it sits high for what it's supposed to be. Thanks.
  2. Anyone? Anything else I should be looking at?
  3. Ah forgot to mention, brand new KYB 4513 when I did everything else. I wouldn't say it really floats just driving, but there is barely any feedback when going over bumps in the front. Rear end there is.
  4. Hi all, Been a good while since posting. I rebuilt the entire front end on the 70 Monte, but it still seems like there's a lot of "soak" in the front. Like when I go over speed bumps, the travel seems to soak up almost the entire bump and there is little feedback. Is this stock big body stuff, or do the springs seem too long? It looks a little high. The front end has Speedway tubular upper/lower CA, Moog balljoints, 6330 springs, and 245/60/15 MT Sportsmans on Rallys. Engine is a 305 and the car still has the heater box, but no AC compressor. Thanks for any info. -David
  5. Roger that, thank you gentlemen.
  6. Hi all, Working on a much needed brake job. Noticed the master/booster is pretty tilted back. This looks normal? Seems like it impacts fluid level? Thanks, David
  7. Dennis, I'm not sure either. I haven't noted any serious rubbing from the front even lock-lock. But I haven't investigated it in depth just yet. This isn't a very good picture because my driveway is slanted, but the front end is quite up in the air. I have an all new front end to put on it, but it drives very floaty right now. I think you're right and I'll probably give 245/60/15 on the front and keep the 275/60 on the back. I'm not really sure how the front tires are fitting, I feel like something odd is going on up front haha.
  8. Hi all, Looking to get new front rubber for my 70. Currently, it has 275/60/15 on all four corners and handles like a boat. I do like the 275s in the back and like the height of the rear as it sits currently. But the front definitely needs to come down a couple inches. Which would be more preferable? A 225/70/15 or a 235/60/15 with keeping the 275/60/15 in the rear? I do like the forward rake look, but want this thing to handle better. Thanks! -David
  9. Christmas for the Monte Everything is looking pretty good. I went with Moog lower ball joints to get pressed into the Speedways as well. I'll probably get the uppers at some point, but I'll keep a close eye on the Speedway ones for now. New rotors, pads, control arms, springs, shocks, steering linkage, and a beefier sway bar. Time to bring the front end back down to earth and see if I can reduce some of this boat's body roll.
  10. Awesome! Didn't know those were a direct fit, those look much better. Gotta show off my cheapy upper tubular control arms Mine are all kinds of cracked and the fenders are flopping around while driving because none of it is bolted together haha. I would think steel would offer a little more support. I'll also be relocating the battery to the trunk, so should clean it up a bit more. Thanks for the feedback and pics!
  11. Ahhh so is there something that can work with the Monte fenders? You've got my interest now
  12. Definitely agreed. I'd try to put something to cover the tire, but still not take up all the room the plastics do. Very true. I'm thinking of something (probably some thinish gauge sheetmetal) to "seal off" the inner fender and form an arch over the tire. Something more flush with the fenders and could still use the same bolt locations. Just malling things over since my plastics are pretty beat up and I like a cleaner engine bay. I'll see if I can photoshop something, just thought I'd see if anyone had something similar or ran without them.
  13. Hey all, Curious if anyone runs without the plastic inner fenders on their Monte. I was really interested in the Tokyo Drift Monte Carlo and like the open engine bay look without them. I know that it would kick a bunch of crap up into the engine bay, but curious if anyone has driven without them and how bad it is. Thinking about making something to still brace the fenders but not be as big as the plastic ones.
  14. Awesome, thanks for the feedback. How are they working out for you? That was my thoughts too, I was going to replace the control arm bushings with poly and all of the ball joints. Taking that out of the price it was about $150-200 for brand new tubular control arms with that stuff installed. They can't really be THAT bad can they? The Chevelle guys seem to think they crack? I have no idea, it might have had a big block at some point. It just seems like the front end "soaks" up bumps with travel while the rear acts more proper. A large portion of this may be caused by the big tires, I'll be fixing that too. I will take a look at the steering box, I'm not 100% it is stock, but it does seem to work pretty well and the play isn't intolerable. I do think the passenger side outer tie rod is tweaked though, it just doesn't look straight. I do have plans to do a drop spindle, and made sure that they would be compatible with the speedway arms. I was just going to clean up the stockers and put some cheap new rotors on this time around. Plan will be to get drilled/slotted and some proper calipers on drop spindles with stainless lines when I save up some more later. Yeah, I'll take a look at the tires, I'm thinking either a 225/70 or a 235/60 with the MT Sportsman S/T.
×
×
  • Create New...