Regmon

Hello. Has anyone used a umi 4034-B reas sway bar and had issues with it not fitting between the lower control arms? I have a set of umi 4024-B non-adjustabe boxed lower control arms and I just purchased a umi rear sway bar 4034-B and I could not get them between the control arms, they seemed to be about a 1/2" to wide. Has anyone else run into the before. Thanks

very nice...

Watch where you get your quarter panels from. I got mine from OPGI. My body guy said the line in the quarter ran off where the quarter extension meet the quarter panel. I don't know if it was true, but I was pissed.. but in the end he did get it right.

I to have received that email and I renewed back in January. My credit card had the charge on it. What's up with that?

I got my pod for a 72 from Summit and it was the restoparts brand.. it was very good quality.

Good day..just thought everyone might like this. https://youtu.be/CAggDusGPNY

I learned something new today.Thanks for your input...

I just finished the idiot light to gauge conversion and eliminate that part. So what you saying is if i have a floor shift column and attatch the the back drive the bowl would move just like the bowl on a column shift column..?

ANOTHER QUESTION..IF I CHANGE THE COLUMN TO A FLOOR SHIFT COLUMN, THEN I WOULD HAVE TO CHANGE THE NEUTRAL SAFETY SWITCH & BACK UP LIGHTS AND EVERY THING ELSE TO THE FLOOR SHIFT SET UP CORRECT? RIGHT NOW I AM STILL USING THE COLUMN SHIFT COLUMN AND DIDN'T NEED TO CHANGE ANY OF THE WIRING FOR THAT.. WOULD BE BETTER TO JUST CUT OFF THE BOSS OR TRY TO GET A NON-TILT FLOOR SHIFT BOWL AND TRY TO MAKE IT WORK WITH MY EXISTING COLUMN..WHAT DOES EVERYONE THINK ABOUT THAT?

yes bruce it really is a small world...gilbert is not far from my house...by the way you have a fantastic monte!!! are you from this area? and was the monte from here to?

Thomas, who is the company that has a sleeve for the tilt column conversion?

my column is a non-tilt but if anyone has a tilt floor shift column i would be open to discuss. Larry i sent you a PM.

Hello everyone. I have a question on my steering column, I changed mine from column shift to floor shift. and was looking for a replacement sleeve without the shift handle piece to replace my existing sleeve and make it look like a original floor shift column. I seen some videos where the piece is removed by cutting it off and doing some patch work to fill in the area. but before i dive into something like that i was checking to see if there was a replacement out there that would work, or if anybody has another solution without changing out the complete column. thanks for reading my post. any advise is appreciated.

Good day everyone...re-doing the dash and noticed the heater/ac duct pipe is in bad shape. looks to be some kind of fabric hose with a spiral wire for support. the section by the pass. side measured 3". does anybody have suggestions for replacement hose & where to get it. thanks for any help you can provide.

Thanks for the help. I got them out and installed the other's to there locations...

Hello, can anyone tell me how to remove the wires from the dash cluster harness plug. I'm doing the sunnies gauge conversion and I'm at trying to remove the wire from harness. Any help is appreciated.

No really, I have the whole car on the bench...but no battery..ROF...LOL

Have you or anyone done this on the beach using a different power source other than the wiring harness from the the car?..

hello, i am upgrading my dash to the gauge set up from sonnies and I have the cluster removed. I was wondering if there is a way to test the dash lights after upgrading to led before i put the gauge cluster back in the dash? Any info is appreciated. Thanks

Thanks everyone for the recommendation. I will look for all them online and decide on a cover...thanks again. And if rsorg decides to part with his custom drop me a line...thanks all!

Good morning everyone. I was wondering if anyone has any suggestions on a indoor car cover. I would only be using it in the garage for storage. I'm looking for one that won't scratch or make swirls in black base coat clear coat paint job. If anyone has something that they recommend it would be appreciated. Thanks and have a great day..

I did not weld the nut in, And my plan is to use some sort of body plug to repair the cut area's. Ill post the pics when I get it done.

I will keep you in mind. Thanks

Thank guys, there were 2 dimples in the trunk and they were the bolts I was looking for. All replaced and done. These are pics of the spots in the trunk for the 2 just behind the rear wheels. now to repair the spots in the trunk..thanks for your help...

Any tips on what to look for in the truck where they might be located? I have already figured out where the ones at the bumper are located though the trunk area...thanks