bigscaht Posted March 6, 2013 Posted March 6, 2013 u stole my tahoe to go get them in..hahahah I ordered my replacement trunk floor pans..jus the center and left section...time to break the welder back out!
abe72 Posted March 6, 2013 Posted March 6, 2013 Once the vinyl came off, this is what we found. A small hole,lower left corner rear window. I was surprised that was all, overall the top looked good. Gonna use fiberglass to repair.
Mike G Posted March 6, 2013 Posted March 6, 2013 LOL! I will bright it back after I am done with it... u stole my tahoe to go get them in..hahahah I ordered my replacement trunk floor pans..jus the center and left section...time to break the welder back out!
LostnFound Posted March 6, 2013 Posted March 6, 2013 Abe, I would cut out all the rust around that spot and have a new piece welded in. Fibreglass is good for a daily driver but it doesn't last. Just my 2 cents. Cheers, Larry
GREENSHOTRODS Posted March 7, 2013 Posted March 7, 2013 Post filter, regulator, feed and return lines done ! The best part...NO LEAKS !!
MCfan Posted March 7, 2013 Posted March 7, 2013 Looks great, Abe! Better go cruisin' now to show it off!!
LostnFound Posted March 7, 2013 Posted March 7, 2013 Abe...that looks great....looks like they did a quality job.
LS5 Posted March 8, 2013 Posted March 8, 2013 Even know I knew the monte was built real early in 1969, i also got confirmation when i went to change all the bulbs in the cluster today when they were all 1849's which were the twist lock bulbs in the tower sockets instead of the 194's in most monte's.... I switched to the short plugs and instead of going with the 194's that have 2-3 burning Candle lite i went with a 588 with the built in magnifine glass tip in them to increase each socket to 9 candles each so that will brighten things up in the monte..... If you remember I did the same in the 70 Chevelle and it did as the posting i put said at that time the "Clark Griswald Effect"..... Cant wait to test it out just gotta get help putting in the whole dash which is an ac dash to boot...... Uggggg. Darren.
Ian Posted March 9, 2013 Posted March 9, 2013 Finally took mine out of the trailer put some fresh gas in her and took it for a couple rides. One to drop my daughter off at a friends and one to take my son to the mower store to get parts for his latest small engine he found at a pawn shop. Big Block burnouts are fun.
monte70car Posted March 9, 2013 Posted March 9, 2013 Wednesday I had some parts show up. I haven't really been feeling good to work on putting many on . Thursday I took the small items out to the garage and put the wire retainers on the drivers inner fender to hold the new harness the fiber optic line and the water sender harness so it's now back in the stock location before it was between the inner fender and the fender(yes it was a cleaner look but a paint to get the wires in that location). Don't worry about those two wires by the steering box they haven't found a home yet might use them for the elec fan setup along wit the elec. wire and a relay.
502ci Posted March 10, 2013 Posted March 10, 2013 I rotated it 180 degrees in the garage...it was facing in, now it is facing out...
7tonemonte Posted March 10, 2013 Posted March 10, 2013 I rotated it 180 degrees in the garage...it was facing in, now it is facing out... Out is a good way to face Bill, sign that it will be making a trip outdoors soon!
monte70car Posted March 10, 2013 Posted March 10, 2013 Got the inside and engine side heater box mounted and one heater hose run. Today its back to the project hood for a few hours of work and maybe paint some kick panels.
502ci Posted March 10, 2013 Posted March 10, 2013 didn't touch mine, fell asleep on the couch The day is not over...you should be refreshed enough to work on it till after midnight now...
footballubet Posted March 10, 2013 Posted March 10, 2013 Well that should have taken about 5 minutes! Nothing in the way.
stangeba Posted March 10, 2013 Posted March 10, 2013 Love it! Did you ever get a 5 speed or is this going to have the 4 speed? Bruce
Sam (Bones) Posted March 10, 2013 Posted March 10, 2013 the M20 is going back in it, it cost $640 to have it rebuilt and it's the matching numbers tranny
Mo's70MCs Posted March 10, 2013 Posted March 10, 2013 well it's in!!! Sweeet!! except for the Chinese parts..
Recommended Posts