[My First Eastern Meet]

I was hooked also the first time we went to a meet. I don't regret any of it. Can't wait to see you all again. Thanks for posting the pic. More great memories.

 

Mike G

[Lets hear it for Rob!]

Nice job to all of you guys. Everything is always perfect. Thanks hor all the hard work in making it happen.

[Side Headliner Moldings]

Thanks. Good to know. I think I see my car in your signature. Nice! lol

The Chevelle one's should be the same.

[Side Headliner Moldings]

I will let you know Bob. I may have a used set coming for a Monte. I am waiting to hear back if they are ok.

 

Cory, The ones I have do look ok but they are to skiny and they do look ok but it drives me nuts that they are not wider like the factory ones.

[Side Headliner Moldings]

Anyone know if the Dynacorn M1460D ones they make for the Velli will work on the Monte?

Thanks

[What did you do to your Monte Carlo today?]

Fixed my fuel gauge. Loose tan wire on the fuel tank. that was the fastest half a tank of gas I ever when through.

[What did you do to your Monte Carlo today?]

Drop off her off for custom front pipes made!

[10 bolt to 12 bolt Moser]

Ohhhhh ya! I will make up for it with a 700 R4. Lower 1st gear over the TH350. Even more smiles. Heehee

[10 bolt to 12 bolt Moser]

Thanks Dave,

 

54 1/2 was the magic number. Dropped the d/s this morning and it will be done later today. One step closer to testing out the 3:73's

[10 bolt to 12 bolt Moser]

Going from a stock 10 bolt to a Moser 12 bolt do I need to shorten the drive shaft? The drive shaft looks longer now.

[What did you do to your Monte Carlo today?]

2 months! That will put you at July 6th. You will miss the EM.

[What did you do to your Monte Carlo today?]

Pulled out the 10 bolt this weekend and stated to clean up the trailing arms for some paint and new bushings.

[What did you do to your Monte Carlo today?]

Pulled out the 10 bolt this weekend and stated to clean up the trailing arms for some paint and new bushings.

[Rear Brake Lines Needed]

Thanks guys and yes I am going with Stainless. LOL I guess I need to post over at "What did you do to your Monte today" Purchased Chevelle brake lines.

[Rear Brake Lines Needed]

Here is a good one. Hope someone can point me in the right direction.

 

I am replacing the 71 Monte 10 bolt with a Moser 12 bolt from a 66 Chevelle.

 

Do I buy rear lines for a 66 Velli or a 71 monte?

 

Thanks,

[Set up 12 bolt rear, eaton posi, 3.55 gears, plus]

I have been looking for a while for one for mine and I have seen GM 12 bolt ones run from $400 up to $1200 for a good one. After taking my time I found a Moser 12 bolt with 3:55s ready to go with 2k miles on it for $1500. Came out of my buddies 66 Velle. Now I have an extra inch in the back to make up for rear discs or fatter tires.

[What did you do to your Monte Carlo today?]

LOL! I will bright it back after I am done with it...

u stole my tahoe to go get them in..hahahah

I ordered my replacement trunk floor pans..jus the center and left section...time to break the welder back out!

[Custom Center Consoles]

Thanks! I'm a sign maker so I may have to ask my distributor if they stock it. Cool!

 

Mike, take a look into 3M's Di-Noc series of woodgrain vinyl. They have a burlwood pattern, how well it would match I do not know, but this stuff works great for heating, stretching, and wrapping pieces. I hope this helps.

Tom

[What did you do to your Monte Carlo today?]

Picked up my custom covered front seats.

 

[color poll]

I am not telling what I voted for!

[Custom Center Consoles]

I plan on doing a full custom console for mine. Does anyone make just a burlewood wood grain material that you can buy?

[Z20 Confirmation!!!]

Congrats!

[Found a keeper ... Build Sheet that is]

Congrats Dennis!

[front end conversion]

Ohhh here we go that the 71 is the best! Ohhh wait. You are right! I have a 71.

 

Well we all know the 71 front end is the best You just cant beat the rectangular turn signals and that purty grill.

[Mig Welder - Advice]

You can't go wrong with one of the top 3. Miller, Hobart and Lincoln. I got to use a Miller 211 when doing my Monte over and love the thing. Now I need to buy one. I blame my body shop guy. But that runs around $1000. DOH!