Batman
-
Posts
34 -
Joined
-
Last visited
Content Type
Profiles
Articles
Forums
Gallery
Events
Posts posted by Batman
-
-
it had a t350. is there a certain amount the yoke should stick out of tail shaft once installed? 1" maybe. u joint is correct.
-
but how do i measure the one i have to make sure it is right?
-
i am doing a 2004r swap in my 70 monte.getting close to putting motor and trans back in.how do i measure dtiveshaft to make sure the stock one will work.searched youtube all i find is how to measure to have one made. seams like im missing something just not getting it. i know yoke has to have room to slide.
-
i have 70 350 4bbl stock.chiltons calls for ac r44.i cant find any.is there another one i can use thats easier to find.
-
i have a 70 with a stock 350 with performer intake and quadrajet.am doing a 2004r swap with 12 bolt 373.while i have engine out might change cam.how would a edelbrock 2102 cam work with stock converter. not looking for a big performance gain.this is a nice daily driver.
-
got it all done.i coulnt get new yoke to go on. i tried a used one that went on good.thanks for all the help i sure was in panic mode.
- 3
-
here is what i figured out.yoke and trany output are 27 spline.my problem is i have a new slip yoke on my driveshaft and i dont know why but it wont go on tailshaft. so i found a used yoke and it slipped rite on.
- 1
-
i read alot of people have made the th350 to 2004r swap. most said drive shaft went rite in.from what i can find the 350 output is 27spline the 2004r is 26.did they change yoke? im having trouble finding one with 26 spline.
-
i counted spines today.my 2004r has 26 output shaft. the slip yoke that was in my th350 has 27 thats why i cant get it to slid in.guess i need a 26 spine slip yoke.if i find one will o.d. be correct.i am going to call builder tuesday see if he knows what is going on
-
when you did this swap did you use the factory trans lines?
-
thanks,yes motor stock +4 bbl.trany built buy a shop that does alot of high perf.tranys.
-
i am swapping my turbo 350 for a 2004r out of 86ss . i tried putting slip yoke from 350 in to the 2004r and goes in about1/8 and binds up.i dont see any burrs or anything that should keep from sliding on. anybody run into this or know what it could be.
-
i have a 1970 will be installing a 2004r out of 86 ss this winter.is there anything i can do with shift indicator from 3 speed auto to 4 speed auto or do i just shift by feel.thanks
-
thanks for help will do and get new one.
- 1
-
i dont know either. just trying to gather the parts i will need.do you know what would have been on a stock 350 2 bbl. sorry bout dumb questions but havnt worked on vintage cars in a long time.
-
could you tell me size?
-
i am doing a 2004r trany swap to my 70. is the flex plat from the th350 the same one i use on the 2004r. the 2004r is out of a 86 ss. it has the ss converter.
-
On 4/9/2022 at 8:23 AM, MC1of80 said:
Yes.
thanks
-
i have a 1970 monte.will a tilt column from a 70-72 chevelle bolt in my car? both are column shift.
-
thanks everyone im going to get the tires and go from there.
-
i could only find that wheel with 4.5 bs.i have no problem taking lip back some.its a very nice monte but mot 100% original.
-
thanks that is alot of good info.
-
i have american torque-thrust d 15 x 8- 4.5 rear spacing.i want to put 275/60r15 ta radial on rear of car.anyone have experience or opinion on this fit?
-
i got one from opgi on order.they wont have till late july.just wanted one now but will wait for nice one.thanks
drive shaft length
in Drivetrain Tech
Posted
thanks