Blackhawk
-
Posts
249 -
Joined
-
Last visited
-
Days Won
4
Content Type
Profiles
Articles
Forums
Gallery
Events
Posts posted by Blackhawk
-
-
All four corners.
-
5 hours ago, madmatt9471 said:
Did you opt for the DRL (Daytime Running Light) on your headlamps?
Thanks,Matt
I have the halogen diving lights, but haven't hooked them up.
-
SEM Landau Black is the way to go. It even helps seal in sticky horn pads.
- 3
-
On my car it used the same screws front and back, but the rear markers used nylon nuts similar to the tail light bezels. I believe they were a different size than anything that I had from the front or rear light hardware kits, I can see if I still have the package this weekend. I just measured the holes and did some measuring at Napa until I found the right one.
- 1
-
I think that I met him at a show in MN and that he isn't a member.
On the username, that's a good question. I wanted an email address or username for something when I was ten and I think I chose it for the band, but it was 25 years ago so I don't quite remember. Once in a while I still get lucky enough to use the name without having to add numbers or letters when joining a site.
- 1
-
I never liked how far the tail light housing stuck out from the factory quarter panel, so I popped the spot welds yesterday, got it wedged out, and welded it back together. Next is to finish the hood and other body work and hope to get it in paint before summer.
Of course no photos, I'm terrible at that.
- 2
-
This is the best deal for Bilstein that I've found:
https://www.jegs.com/i/BMR-Suspension/142/BSN-A-68-72/10002/-1
- 1
- 1
-
-
Another solution would be to run a new power source from the horn relay or starter and trigger a few relays using the ignition spade.
- 2
-
If those are for a Chevelle the clips don't line up like the stock seal.
-
The outer is being made: https://metrommp.com/rear_vertical_quarter_window_sealouter_7072_monte_carlo_cutlass_supreme_alp_5002q/
The inner is not currently being reproduced, but I'm working on getting Metro to make them.
- 3
- 1
-
The kick panel speakers need to have a depth of less than 1-5/8" to not space the driver's side out or clearance the support behind it. My speakers have a 1-13/16" depth and I had to take a dead blow hammer to get the speaker to not hit in the back. I really recommend component speakers to put the tweeter up high, then you'll get the high notes up high and the midbass will be lower where it doesn't matter as much.
- 3
- 1
-
Summit and Jegs are both great on the customer service side, and one sometimes has parts that the other doesn't. I went through a few cowl induction hoods before getting one that was salvageable (horrible packaging for something so large and heavy), and I can only imagine how much Jegs paid shipping them back and forth.
- 3
- 1
-
Check the bolt on the firewall and see if it has a shim between the fender and firewall. I don't have the assembly manual in front of me but I think the gap between the fender and rocker should be around 1/8", what is yours at? Is the gap even from top to bottom or is one more than the other?
- 1
-
Tubular control arms can have a few advantages, but the cheap models typically only have the first:
Weight reduction compared to stock stamped arms.
Shorter length for tall spindles or tall ball joints.
Increased positive caster for a more modern alignment and performance.
-
I'll check this weekend, but your bushings look like they're cranked down in comparison to what I remember mine looking like. They only require about 40 lb-ft.
-
They sell a variety of brackets to mount the valve. I'm not endorsing this site and have never used them, just giving an example.
https://eastcoastchevelle.com/productview.php?cat=Brakes&id=1147102345§ionPID=1
- 1
-
This fell to the backburner while a lot of other home projects were happening, but I dropped my original seals off at Metro Moulded today. I don't know what the timeline is for production but I'll update this thread when I know.
- 1
- 3
-
24 minutes ago, Scott S. said:
Plastic ????
The original emblem on Montelishi is chromed pot metal. (Still not sure how a '71 emblem found it's way onto a '70 grill.) But all the red had faded off.
The repro parts are all plastic now, but not that long ago they were still metal. Must be a big demand for them ???
On my 71 emblem the red is covered by a clear plastic cover, keeping you from repainting it. I assume the new stuff is still pot metal.
- 1
-
https://koniksklassiks.com/product/71-monte-hood-emblem-assembly-1654/
Since these may no longer be available, has anybody restored their original emblem? The plating and metal on mine are good, but the paint under the clear plastic has faded. I bet a heat gun could loosen the adhesive without distorting the plastic.
-
-
Even the aftermarket companies that don't cater to the restoration crowd are moving away from CDs. Alpine doesn't have a receiver with a CD player unless it's a larger navigation unit that uses DVDs, and only half of Kenwood's receivers have CD capabilities. The nice thing with that is that the receivers are getting shorter so installation is easier.
- 1
-
-
I finally got to fix the speed sensor and took it out for a few miles. Didn't go too far because the inner fenders aren't bolted to the fender lip, only on the ends and on top. No pictures because it's in spotty primer, so that'll be next.
- 2
Shock replacement recommendation?
in Brakes and Suspension Tech
Posted
That's what I get for giving away my 'secret'! 😄 I was planning on watching and waiting for the Bilsteins and trying out the Monroes that I threw on the car years ago (and already had to replace one for leaking with less than 5 miles), but 25% off and waiting a few days for the usual $20 off $249 might make me add this to my parts collection for later in the year.