Traveler
-
Posts
139 -
Joined
-
Last visited
-
Days Won
4
Content Type
Profiles
Articles
Forums
Gallery
Events
Posts posted by Traveler
-
-
Carlisle today beautiful
-
3
-
-
had my 71 on jack stands all this week, put in a new fuel tank and gas sender, electric pump and fuel line, and a holley sniper stealth, started first time after using the wizard, the planning, routing and parts runs took more time then the install
-
thanks, that’s the one I was considering
-
Thanks Bob, is it the one sold by Jets that looks like a diaphragm pump and comes as a kit with hose, mounts, switch, wiring...
-
Thanks guys, I’ll take your advice, the list of todo’s is getting shorter lol
-
1
-
-
as part on my rebuild on my 71 I put a 383 stroker motor in with a wild cam. manifold vacuum runs 5-6” at ideal, which lead to a hard brake pedal. i put a vacuum canister in and that definitely helped, once i drive it a little, but at start up i still get a hard pedal. a mechanic told me that early camaro’s had a 9/16” booster check valve, that installing it and running a new 9/16” hose from the manifold would help, but after several phone calls to dorman, jegs, summit, napa... no one can source the part, would anyone know a part number or other fix.
thanks john
-
I had a teacher at RIT that said ‘old age and cunning will overcome youth and enthusiasm every time’ I piped in ‘except in a foot race’, that’s when he told us the story of two roosters in a hen house, lol. Don’t hurt his feelings too much.
Someone posted on this site that ‘Experience is the teacher that gives the test before the lesson’ and I have the scares to prove it LOL.
-
Thanks Tom,
I know there is a ground from the battery to the body, bat to the engine, body to the frame, but cannot locate engine to the body or the frame, so I have another little project to address before Carlisle,
again thanks
-
1
-
-
is there a ground strap from the engine to the chassis/firewall? if yes where is it located on a small block
-
On 1/24/2020 at 9:56 AM, cny first gen 71 said:
No need to say sorry, it was all in fun. A lot of us have blown the budgets right out of the water at one time or another. I'm still curious if the upper control arm works from 10 to 12 bolt because I have a 12 bolt on deck also.
yes the 10 bolt works just fine, I got the correct 12 bolt style and the only difference was the gusset/reinforcement plate, I have not installed it yet still using the 10 bolt, MC1of80 is 100% correct!
motors in, trans in, rear done, in the shop for x pipe, headers, 2.5” exhaust/mufflers, a couple of little things like acc. hot wire for electric chock, new hood hinge, ... budget, close but no cigar, I kept the original drive train and have an offer for the motor which would bring it back in line
-
thanks Paul that’s what it is
-
jets are the same oft power valves are different with larger diagrams and a different port design, jets installed power valve on order
-
called holley they say yes, other sites say they are different, I’ll let you know what i find
-
I’m tuning this new carb and it is rich so I will be rejetting it, are holley and qft jets and power valves the same?
J
-
1971, non ac car, for the time being lol, the bundle goes across the top of the firewall
-
Progress, ya got to love it.
Motor trans and rear are in. 10 bolt to 12 bolt, turbo 350 to 2004R, and 350 2bbl to 383. Cams broke in waiting on oil to do a change and then take her for the first drive. I’m sure there are some surprises waiting for me, but that’s to be expected with sooo many changes.
Still on the list; oil/filter change, adjust the TV cable and bracketry (interference with the air breather drop down cover), electric chock final connection, check the lifter lash, SS dash(havent’t assigned a priority to this yet, probably the first thing after the shake down) inner fender wells, engine bay clean up, new power steering pump old one works fine but just like me old...
List is getting shorter, but I seem to find new items as I go LOL
-
5
-
-
Anybody know what his connector is for. It comes from the bulk head fitting has 4 wires two brown one blue one green with a two terminal plug.
-
Progress ya got to love it, remember when corona was a beer you put fruit in
-
I replaced the bulbs with led’s and found I needed to pull the dash pad to gain access, the dash pad removal is a 10-15 minute job and 6 screws, 4 over the cluster 2 in the glove box. when young I snaked my arm up from under the dash but my arm doesn’t bend the way any more, lol. This still left a couple a little hard to get at.
Paul Bell is correct be careful around the printed circuit sheet when replacing the bulbs, the traces in my case were 48 years old and when I attempted the bulb for the headlight switch the holder moved the copper trace. I was able to get the bulb holder to trap the trace under the contact point when I realized why it wouldn’t light up. I‘ll replace it when I upgrade to a tack instrument cluster in a few weeks. A separate pc board/sheet is available from Sonnie24 on ebay and others as well.
If you choose to pull the dash you may need to drop the steering wheel, good luck.
J
-
hoping to prime the engine and fire it up today , progress ya got to love it
-
Another craftsman who takes pride in his work, looks good
-
If she turns into a -itch it not on me, lol
hope to fire her up this Wednesday, still have power steering pump and lines, carb, fuel pump, prime the engine, complete the trans install(tci kit) reinstall the radiator, shroud, install distributor- still quite a list but it’s getting smaller
-
1
-
-
I always find a name for my cars, her name is Lady. I once introduced a very beautiful girl friend, who I was serious about, to my family after a day at the beach, boy did I hear about that. Something about hair and make up lol. The Monte is a mess and I will post shots once I clean her up a bit. We all know what happens when you disrespect a lady, LOL
J
-
Good morning all,
Has anybody found, or know of a way, to control their electric 2 speed fan by temperature? IE: turn the first speed on at 165*F and the high speed on at 180*F? Temps are unimportant just stated them as examples.
J
What did you do to your Monte Carlo today?
in General 70-72 Monte Carlo Forum
Posted
Once the guy got the blender for the fusion generator running I just had to post the picture, lol not sure what I did but this is one beautiful national champion MC at Carlisle, only one I saw. It drew a great deal of attention