robs70monte

I took the sticker off also

I have the Pertronics Igniter III with the PerTronix 40511 Flame Thrower Coil works great

yes you can inter change 71 and 72 extensions and other front end parts but it requires modification many never done it tho

Funny i have all the steel to finish my chevelle floors but what has it done the past 5 years ummm sit Good luck

You cant put 1971 fender extensions on a 70 core support 70 is all on its own

I got one for you pm me

you and tell the 350 is a small and round the 402 is a small oval and the 454 is a big oval i have 2 454 air cleaners and like a dozen 350 2bbl and 4bbl ones

Well if the fuel bowls leak then it will be hard to start because it will have to pump gas out of the tank till the bowls fill back up,and i don't think you have a q-jet if it has fuel bowls,if its off a 74 vett you have the Have the Holley quadrajet replacement carb its the Holley version of the quadrajet i have one of them and there easy to tune carbs there is no float adjustment there pre set its pretty much jets and A/F screws witch are easy to adjust if you have a vacuum gauge

My body guy made them fit perfectly on my 70 Monte

oh wow i had a brain fart there shift cable not kick down my bad no i feel stupid lol

A TH400 actually has an electric switch for the kickdown. It is sometimes mounted on the carb linkage (in several different places) or can be mounted under the gas pedal (most common) The modulator controls shift points on the 400 til WOT then the detent system takes over and actuates the electric kickdown. The reason for this is because there isn't enough vacuum at WOT to operate the heavier 400 components. WOT shifts without the kickdown hooked up will cause the clutches to slip and they will wear out before you want them to. If I remember right there are aftermarket kits that replace the GM electric switch. rob

You could unhook the hose at the booster and put a big vacuum cap on it and hop in it fire it up and put it in drive and hold the brake if the problem is one its the booster

try a gauge a different gauge like a under hood one with a small lead maybe.

Is it loud or grinding

Ya sounds like a weak starter or bad connections on the starter

you can tell with out taking the apart 8.5s have the ears and the 8.2s don't, its pretty cut and run

the 8.5 10 bolt will have 2 ears on the bottom of the center section the 8.2 is rounded

Leaving the cable off or unhooked won't do any damage to a th-350. It only controlls the 3 to 2 kickdown. Now on trannys that uses a TV (throttle valve) cable like the 700R4 and 200 4R, the cable controlls line pressure and kickdown, so it MUST be hooked up and adjusted right You will just have to manually downshift it i dont run the kick down on my th350 but my motor is a well built 383 and i like to manually shift a lot

You can try to retorque and use sealer and it may work but the question is how long will it work, retorqueing and sealer are a short term fix to a long term problem id plan on doing head gaskets soon

Are you running SYNTHETIC oil? It takes a long time for rings to seat it took my chevelle at least 500 miles to seat the moly rings,Cast rings should seat faster then moly rings

I run them same springs (z28 springs) and my cam is the comp 268h with.454/.454 lift and the cam calls for 110-115 and the Z28 springs 110# @1.700" so you may need a bit more seat pressure

More metal form china lol

What kind of car is it i can look out back at work to see if there's any cars with OK looking axles the set up your car has looks to be the same as the 1980-1987 buick regals and Rivieras

If i was you i would look around the junk yards for a 8.5 10 bolt posi rear end all you need is a posi unit out of it then you can pull out the summit catalog and ordered a ring gear kit This will work for you http://www.summitracing.com/parts/SUM-741001/ and a install kit http://www.summitracing.com/parts/RAT-360K/

3:73 will be great for what your doing i have 3:73s in my big block chevelle and it runs great at the track and on the street my Monte has 3:31s in it and it still doesn't take off the way i want it to its a bit sluggish