Jump to content
Sign in to follow this  
Jared Richey

SS Hockey Sticks

Recommended Posts

I'm putting the call out again for a set of preferably used SS 71 rear hockey sticks. I want to put these in the hands of a few people in this area who have the equipment to make something like this.

I currently have them on one of my cars but as any that is familiar would know it's an act of Congress to take them off. I do not want to be responsible for any NOS ones... Prefer a used set to use. I would be willing to buy a set if the price is right... Or buy them with the agreement that when I'm done with them you can buy them back for the same amount.

Share this post


Link to post
Share on other sites

I talked to someone at the Parts Place and they were going to have there supplier manufactor the upper mouldings but I don't see them listed

Share this post


Link to post
Share on other sites

I'll agree.....way too much work to take them off....... hopefully someone will come up with a set for you Jared.

Mine are in good shape but put me down for a new set once you get this done!

Steve

Share this post


Link to post
Share on other sites

The "hockey sticks" are on a 71 SS car. They are on the back tail panel, on the end caps above the normal trim pieces. The panel is then blacked out between the trim. They look like the lower end cap trim only bent with a tighter curve and are held on with a nut on a stud opposed to screws for the lower pieces. Actually they look like this, off the car.....IMG_20180826_115504.thumb.jpg.8483f5712222e6a13d5c40b489258922.jpgIMG_20180826_115540.thumb.jpg.7a761188d62fbcf082be76b669d15dbd.jpg

IMG_20180826_115520.jpg

IMG_1121.JPG

Share this post


Link to post
Share on other sites

The hockey sticks is the small trim piece that bolts to the end cap on 1971 SS .top piece in picture

0510sc_06z+1972_chevrolet_monte_carlo+rear_view.jpg

Share this post


Link to post
Share on other sites
On 1/6/2019 at 11:22 AM, 1970mcss said:

I talked to someone at the Parts Place and they were going to have there supplier manufactor the upper mouldings but I don't see them listed

Can you call whoever you talked to and verify? If there going to mass produce that would be good. Hopefully they make them out of stainless.

Share this post


Link to post
Share on other sites

Jared do you need both?  I think I have one still attached to a piece not attached to a car, I have to check. Give me a day or so and I will get back to you.

Share this post


Link to post
Share on other sites

Jared, I think it has Joe the owner. He was going to figure out the measurement of the stud location and talk to the people that produce the lower mouldings. I have a 70 so Never followed up. You might want to call them and ask. Good luck and keep us posted...

Share this post


Link to post
Share on other sites

Ok.

Willie, 1 might work, I think it's a flip copy anyway. 

Thanks

Share this post


Link to post
Share on other sites

 Not a flip copy. Look at the pics I posted. Especially of the pair. They are left and right specific and have different part numbers for each. Also hard to see but the studs on the back are in slightly different locations .

Share this post


Link to post
Share on other sites

My response from the parts place...

 

We currently are in the process of making them, please contact us back again on the matter in a few weeks and we may have an update.


 

Share this post


Link to post
Share on other sites

Just sent them another message not quite available yet but says will be available shortly!!

Share this post


Link to post
Share on other sites

No but I just seen your post I'm going to send them another message.

Share this post


Link to post
Share on other sites

I have not heard back it's been a few months so I need to send another email. if it's like other new parts it always takes three times as long. 

Share this post


Link to post
Share on other sites

Just sent them another message they said they are almost in stock to check back in a couple of weeks!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...