Engine Tech - Archive

199 topics in this forum

1. Solid roller lifters on a hyd roller cam?

   By Heckeng, December 21, 2007
   • 5 replies
   • 2.8k views
   • 
   • Heckeng
   • December 25, 2007

2. FYI on new 72 gas tanks

   By 1972mc, December 18, 2007
   • 6 replies
   • 2.5k views
   • 
   • Nygel
   • December 22, 2007

3. 496 big block info

   By Guest Rice Racing1, November 20, 2007
   • 9 replies
   • 5.2k views
   • 
   • Phil
   • November 28, 2007

4. compression check 1 2

   By vince, September 21, 2007
   • 25 replies
   • 21.7k views
   • 
   • Guest
   • September 27, 2007

5. msd 8981

   By 71monteme, September 11, 2007
   • 3 replies
   • 2k views
   • 
   • Guest
   • September 14, 2007

6. OIL

   By Guest Torquemonster, July 29, 2007
   • 6 replies
   • 3.1k views
   • 
   • stangeba
   • July 30, 2007

7. Performer RPM and Holley Carbs

   By mc71454, June 24, 2007
   • 4 replies
   • 2.7k views
   • 
   • mc71454
   • June 27, 2007

8. Spacer Comparison - Open, 4-hole and none

   By mc71454, June 24, 2007
   • 5 replies
   • 2.3k views
   • 
   • 680HPStroker
   • July 2, 2007

9. Better street engine? 1 2

   By Heckeng, May 31, 2007
   • 29 replies
   • 15.2k views
   • 
   • stangeba
   • June 6, 2007

10. vortec heads and intake

    By monte70car, March 19, 2007
    • 13 replies
    • 5.8k views
    • 
    • monte70car
    • March 21, 2007

11. Hyperuetic pistons for sub-500 hp engine?

    By Guest, March 8, 2007
    • 8 replies
    • 2.5k views
    • 
    • Guest
    • March 9, 2007

12. Are vortec's REALLY worth it?

    By kc8oye, March 7, 2007
    • 4 replies
    • 1.9k views
    • 
    • 72 LS5
    • March 9, 2007

13. Bottom end advice?

    By kc8oye, February 17, 2007
    • 15 replies
    • 6k views
    • 
    • kc8oye
    • February 27, 2007

14. Main stud girdle

    By Reaper, February 16, 2007
    • 6 replies
    • 1.9k views
    • 
    • Sam (Bones)
    • February 17, 2007

15. xe274 w/1.6 roller tip rockers

    By AL M, February 12, 2007
    • 5 replies
    • 2.1k views
    • 
    • AL M
    • February 25, 2007

16. Holley Intake vs. Performer

    By gprimm, February 11, 2007
    • 9 replies
    • 3.1k views
    • 
    • Guest
    • February 15, 2007

17. bushed vs. press fit rod strengths

    By Heckeng, February 7, 2007
    • 15 replies
    • 10.6k views
    • 
    • wallaby
    • February 12, 2007

18. Big Block intake?

    By wallaby, January 31, 2007
    • 12 replies
    • 6.1k views
    • 
    • wallaby
    • February 2, 2007

19. Mechanical water temp gauge

    By laurent, January 30, 2007
    • 14 replies
    • 5.5k views
    • 
    • kc8oye
    • February 17, 2007

20. Vacuum/Timing

    By wallaby, December 30, 2006
    • 10 replies
    • 5.1k views
    • 
    • Mike 57
    • January 12, 2007

21. Big Block Header Recommendations? 1 2

    By MonteAZBB70, December 28, 2006
    • 47 replies
    • 35.4k views
    • 
    • Guest
    • March 11, 2007

22. Good small block headers?

    By MikeResko, October 19, 2006
    • 16 replies
    • 9.2k views
    • 
    • 70Monterrs
    • July 17, 2007

23. large displacement SBC questions

    By Heckeng, October 11, 2006
    • 7 replies
    • 3k views
    • 
    • Mike 57
    • October 12, 2006

24. Alternator Pulley Upsize

    By Guest, October 10, 2006
    • 6 replies
    • 2.4k views
    • 
    • Mike 57
    • October 12, 2006

25. Carb tuning with Wide Band O2

    By Heckeng, September 23, 2006
    • 6 replies
    • 2.7k views
    • 
    • Monte
    • September 24, 2006